Search

  • Statut des commandes
  • Commande rapide
  • Promos
Particle Size Analyzer PSM-500
Particle Size Analyzer PSM-500
Particle Size Analyzer PSM-500
Particle Size Analyzer PSM-500
Thermo Scientific™

Particle Size Analyzer PSM-500

The Thermo Scientific Particle Size Analyzer PSM-500 provides real time, in-stream particle analysis of up to three streams.
Have Questions?
Référence PSM-500
Prix (EUR)
-
The Thermo Scientific™ Particle Size Analyzer PSM-500 provides accurate feedback for the optimization of grinding circuit performance helping customers not only to enhance mineral recovery and quality but also to optimize their energy efficiency during the process. This unit is a rugged on-line Particle Size Analyzer which pulls its own continuous sample using a vacuum eductor. To assist with the ultrasonic measurement, the sample is de-aerated in the sample conditioner before it passes between diametrically opposed ultrasonic sensors and is returned to the process.

Features

  • Robust with Ingress Protection Rating IP65.
  • Rugged internals, NEMA approved 4X corrosion resistant.
  • All new software and contemporary user interface.
  • Higher bandwidth and field replaceable transducers.
  • No dilution required.
  • % of solids measurements is standard.
  • Improved alarms, status display and reports.
  • No UPS needed.
  • Full colour intuitive local touch-panel user interface.
  • No pumping.
  • Size range between 1 to 1000 microns (can be optimized according to application).
  • Data are typically accurate to better than 1% absolute.
  • High availability.
  • Ultrasonic hard ware.
  • Measurement updates time, typically 10 sec.
  • Upgradable from PSM-400MPX.

Benefits

  • Enhances mineral recovery by providing accurate analysis of particle size distribution and percent solids.
  • Increases energy efficiency by assisting the grinding control with the recovery and the throughput of minerals.
  • Designed to work in the harshest environment conditions with temperature compensation and wider operation range.
  • Easy to be calibrated through the new modern interface and control systems.
  • Increased signal performance thanks to the new flow cell transducers.
  • Lower cost of ownership since transducers are field replaceable.
  • Lower maintenance
Spécifications
Densité2.0 to 5.5 SG for dry solids
DescriptionAnalyseur de taille de particules en ligne PSM-500
DiamètreMaximum Transport Diameter: <2.3 mm @ <1% retained by Wt. @ 2.7 SG, <1.2 mm @ <1% retained by Wt. @ 5.1 SG
Alimentation électrique380/600 V 50/60 Hz 3 Phase
Connexions électroniques à l’analyseurCAT5/6/6e network cable directly to analyzer (less than 100m in length)
Boîtier électroniqueIP65; CE; ICES 001, CSA, FCC Part 15B and RCM
EnvironnementDirect exposure to sunlight and ultraviolet radiation is not permitted. Not rated for unprotected, out-of-doors operation
Air de l’instrumentMinimum Pressure - 552 kPa; Maximum Pressure - 1034 kPa; Maximum Flow - 17m3/h @ 690kPa
MatériauWetted parts: engineering polymers or rubber covered steel
Température de fonctionnementAmbient -10°C to +50°C Operating Altitude: 0 to 5000 mts
Pourcentage de solides% Solids Wt 10% Minimum to 60% Maximum, % Solids Vol 3% Minimum to 26% Maximum
Assurance qualitéAdelaide manufacturing facility ISO-9001:2000 certified
Type d’échantillonChemical: Caustic slurries up to PH of 12.5
Eau de standardisationClean potable, Flow 6 to 18 L/Day
Revêtement de surfaceCommercial sandblast, surface preparation, polyurethane fill primer two part epoxy color finish
VibrationsNot to exceed 10G at 20Hz
Eau pour l’acquisition d’échantillonsMinimum Pressure 276 kPa, Maximum Pressure 689 kPa, Flow 45 L/min.
Unit SizeEach