Particle Size Analyzer PSM-500

The Thermo Scientific Particle Size Analyzer PSM-500 provides real time, in-stream particle analysis of up to three streams.

카탈로그 번호	설명
PSM-500	PSM-500 On-line Particle Size Analyzer

카탈로그 번호 PSM-500

제품 가격(KRW)

견적 요청하기

PSM-500 On-line Particle Size Analyzer

The Thermo Scientific™ Particle Size Analyzer PSM-500 provides accurate feedback for the optimization of grinding circuit performance helping customers not only to enhance mineral recovery and quality but also to optimize their energy efficiency during the process. This unit is a rugged on-line Particle Size Analyzer which pulls its own continuous sample using a vacuum eductor. To assist with the ultrasonic measurement, the sample is de-aerated in the sample conditioner before it passes between diametrically opposed ultrasonic sensors and is returned to the process.

Features

Robust with Ingress Protection Rating IP65.
Rugged internals, NEMA approved 4X corrosion resistant.
All new software and contemporary user interface.
Higher bandwidth and field replaceable transducers.
No dilution required.
% of solids measurements is standard.
Improved alarms, status display and reports.
No UPS needed.
Full colour intuitive local touch-panel user interface.
No pumping.
Size range between 1 to 1000 microns (can be optimized according to application).
Data are typically accurate to better than 1% absolute.
High availability.
Ultrasonic hard ware.
Measurement updates time, typically 10 sec.
Upgradable from PSM-400MPX.

Benefits

Enhances mineral recovery by providing accurate analysis of particle size distribution and percent solids.
Increases energy efficiency by assisting the grinding control with the recovery and the throughput of minerals.
Designed to work in the harshest environment conditions with temperature compensation and wider operation range.
Easy to be calibrated through the new modern interface and control systems.
Increased signal performance thanks to the new flow cell transducers.
Lower cost of ownership since transducers are field replaceable.
Lower maintenance

밀도2.0 to 5.5 SG for dry solids

설명PSM-500 On-line Particle Size Analyzer

직경Maximum Transport Diameter: <2.3 mm @ <1% retained by Wt. @ 2.7 SG, <1.2 mm @ <1% retained by Wt. @ 5.1 SG

전기 요구사항380/600 V 50/60 Hz 3 Phase

분석 장치로 전자 장치 연결CAT5/6/6e network cable directly to analyzer (less than 100m in length)

전자 장치 인클로저IP65; CE; ICES 001, CSA, FCC Part 15B and RCM

환경Direct exposure to sunlight and ultraviolet radiation is not permitted. Not rated for unprotected, out-of-doors operation

기기 공기Minimum Pressure - 552 kPa; Maximum Pressure - 1034 kPa; Maximum Flow - 17m3/h @ 690kPa

물질Wetted parts: engineering polymers or rubber covered steel

작동 온도Ambient -10°C to +50°C Operating Altitude: 0 to 5000 mts

백분율 고형물% Solids Wt 10% Minimum to 60% Maximum, % Solids Vol 3% Minimum to 26% Maximum

품질 보증Adelaide manufacturing facility ISO-9001:2000 certified

샘플 종류Chemical: Caustic slurries up to PH of 12.5

표준화 물Clean potable, Flow 6 to 18 L/Day

표면 코팅Commercial sandblast, surface preparation, polyurethane fill primer two part epoxy color finish

진동Not to exceed 10G at 20Hz

샘플 확보용 물Minimum Pressure 276 kPa, Maximum Pressure 689 kPa, Flow 45 L/min.

Unit SizeEach